GAS SAFE
Gas Line Installation & Repair in Tempe, AZ
A new run for a range, dryer, pool heater or BBQ, or a suspected leak. Sized, pressure-tested, permitted and left safe.
- Licensed and insured
- Diagnosed and quoted first
- Answered 24 hours
Gas work is the part of plumbing where doing it exactly right is not optional. A new gas run for a range, a dryer, a pool or spa heater, a tankless water heater or an outdoor BBQ has to be sized for the appliance's demand, joined properly, pressure-tested, and permitted, because the failure mode is not a puddle, it is a leak. And a suspected gas leak is an emergency: if you smell gas, you leave and call from outside, and we treat it that way.
We install new gas lines and repair existing ones across Tempe, and every job ends the same way, pressure-tested to confirm it holds and permitted so it is documented and inspected. There is no cutting corners on gas.
New gas runs, sized for the appliance
The most common reason to add or upsize a gas line is a new appliance that draws more than the existing line can feed. A tankless water heater in particular fires with a large gas load, and an undersized line is the top reason a tankless underperforms. Pool and spa heaters, gas ranges, outdoor kitchens and BBQ stubs all need a line sized to their real demand and to the total load on the system. We size it correctly the first time so the appliance actually gets what it needs.
Signs of a gas problem, and what to do
Treat any of these seriously:
- A rotten-egg or sulphur smell near an appliance or line, leave and call from outside
- A hissing sound near a gas connection or meter
- A pilot that will not stay lit, or appliances underperforming
- A gas bill that climbed with no change in use
- Dead or discoloured vegetation over a buried gas line outside
Why gas work is permitted and pressure-tested, always
Gas is the one area where the permit and the test are non-negotiable. Arizona requires gas work to be permitted and done by an ROC-licensed contractor, and a proper install is pressure-tested to prove the line holds before it is put into service. Buried lines are located through Arizona 811 before any digging so nothing else underground gets struck. This is not bureaucracy, it is the difference between a safe line and a hazard hidden in a wall. We do every gas job this way, without exception.
Materials, bonding and what the inspector looks for
Gas work in the Valley uses a couple of common materials, and each has rules that matter. Traditional black iron pipe is threaded and sealed at every joint; flexible corrugated stainless tubing, often called CSST, runs faster but has to be properly bonded to the electrical ground so a nearby lightning strike cannot damage it, a detail that is easy to miss and important here. Whatever the material, the inspector wants to see the line sized for the appliance load, joined correctly, pressure-tested and holding, and any buried section located through Arizona 811 before it went in. We build to those requirements as a matter of course, because gas is the one system where an install that merely looks finished is not the same as one that is actually safe, and the test and the permit are what prove the difference.
Gas work most often pairs with a tankless heater or water heater install that needs the right gas supply, and larger runs go through our installation and commercial process. We handle gas across Tempe and into south Scottsdale.
Questions
Gas Line Installation & Repair questions
I smell gas. What should I do right now?
Leave the area, do not switch anything electrical on or off, and call your gas utility and us from outside once you are clear. A gas smell is an emergency, not a wait-and-see. Once the immediate danger is handled, we locate and repair the leak and pressure-test the line before it goes back into service.
Do I need a new gas line for a tankless heater?
Often, yes. A tankless water heater fires with a much larger gas load than a tank, and an undersized existing line is the most common reason a tankless underperforms. We check whether your line and meter can feed it and upsize the run if they cannot, so the unit actually delivers.
Is gas work always permitted?
Yes, and it should be. Arizona requires gas work to be permitted and done by an ROC-licensed contractor, and a proper job is pressure-tested to confirm the line holds. That documentation and testing is exactly what keeps a gas line safe, so we never skip it.
Can you run a line for a BBQ or pool heater?
Yes, those are common jobs, an outdoor BBQ stub, a pool or spa heater, an outdoor kitchen. We size the line for the appliance and the total system load, run it safely, pressure-test it and permit it, with any buried section located through Arizona 811 first.
Need a plumber in Tempe?
Call and describe the problem. You will reach a plumber who diagnoses and quotes before any work starts.